Wire rope slings are popular because they are kink resistant and provide strength and flexibility. Wire rope slings are easier to use and less expensive than chain slings. They are usually the best choice for extremely heavy lifting.
End Fittings | ||||||
---|---|---|---|---|---|---|
Various end fittings and end fitting combinations are available for online quotation, where you can choose the complete configuration of the sling that you require. If you require any additional features such as fibre core, or the construction of the wire e.g. 6×36 IWRC, please add this into the additional information box at the end of constructing your wire ropes | ||||||
Ending Types | ||||||
Please see the image below for letter references, the end fitting choices which are choices on the buy/quote tab are as follows | ||||||
A – Fused and tapered | ||||||
B – Ferrule secured thimble hard eye | ||||||
C – Ferrule secured soft eye | ||||||
D – Flemish eye, ferrule secured according to Din 13414-1. (Also known as Euroloop or Superloop) | ||||||
E – Captivated shackle (permanent) | ||||||
F – Master Ring | ||||||
G – Sling Hook | ||||||
H – Self-locking hook | ||||||
I – Foundry hook. | ||||||
J – Swivel Sling Hook.K – Swivel Self-locking hook | ||||||
Maximum Safe Working Loads with Different Slinging Methods | ||||||
EN 13414-1 Table 4 – Working load limits for slings using steel cored rope of classes 6×19, 6×36 and 8×36 | ||||||
Safe Working Load (tonnes) | Nominal rope | |||||
Endless | 3 Leg and 4 Leg | 2 Leg | 1 Leg | |||
1.2 | 1.1 | 1.55 | 0.75 | 1.05 | 0.75 | 8mm |
1.5 | 1.4 | 2 | 0.95 | 1.3 | 0.95 | 9mm |
1.35 | 1.7 | 2.4 | 1.15 | 1.6 | 1.15 | 10mm |
2.25 | 2.12 | 3 | 1.4 | 2 | 1.4 | 11mm |
2.7 | 2.5 | 3.55 | 1.7 | 2.3 | 1.7 | 12mm |
3.15 | 3 | 4.15 | 2 | 2.8 | 2 | 13mm |
3.7 | 3.4 | 4.8 | 2.25 | 3.15 | 2.25 | 14mm |
4.8 | 4.5 | 6.3 | 3 | 4.2 | 3 | 16mm |
6 | 5.65 | 7.8 | 3.7 | 5.2 | 3.7 | 18mm |
7.35 | 6.9 | 9.8 | 4.6 | 6.5 | 4.6 | 20mm |
9 | 8.4 | 11.8 | 5.65 | 7.8 | 5.65 | 22mm |
10.6 | 10 | 14 | 6.7 | 9.4 | 6.7 | 24mm |
12.5 | 11.5 | 1.5 | 7.8 | 11 | 7.8 | 26mm |
14.5 | 13.5 | 19 | 9 | 12.5 | 9 | 28mm |
19 | 17.5 | 25 | 11.8 | 16.5 | 11.8 | 32mm |
23.5 | 22.5 | 31.5 | 15 | 21 | 15 | 36mm |
30 | 28 | 39 | 18.5 | 26 | 18.5 | 40mm |
36 | 33.5 | 47 | 22.5 | 31.5 | 22.5 | 44mm |
42 | 40 | 55 | 26 | 37 | 26 | 48mm |
50 | 47 | 66 | 31.5 | 44 | 31.5 | 52mm |
58 | 54 | 76 | 36 | 50 | 36 | 56 |
67 | 63 | 88 | 42 | 58 | 42 | 60 |
1.6 | 1.5 | 2.1 | 1 | 1.4 | 1 | leg factor KL |
EN 13414-1 Table 3 – Working load limits for slings using fibre cored rope of classes 6×19, 6×36 and 8×36 | ||||||
Safe Working Load (tonnes) | Nominal rope Ø | |||||
Endless | 3 Leg and 4 Leg | 2 Leg | 1 Leg | |||
1,10 | 1,05 | 1,50 | 0.7 | 0.95 | 0.7 | 8mm |
1,40 | 1,30 | 1,80 | 0.85 | 1.2 | 0.85 | 9mm |
1,70 | 1,60 | 2,25 | 1.05 | 1.5 | 1.05 | 10mm |
2,12 | 1,95 | 2,70 | 1.3 | 1.8 | 1.3 | 11mm |
2,50 | 2,30 | 3,30 | 1.55 | 2.12 | 1.55 | 12mm |
2,90 | 2,70 | 3,85 | 1.8 | 2.5 | 1.8 | 13mm |
3,30 | 3,15 | 4,35 | 2.12 | 3 | 2.12 | 14mm |
4,35 | 4,20 | 5,65 | 2.7 | 3.85 | 2.7 | 16mm |
5,65 | 5,20 | 7,20 | 3.4 | 4.8 | 3.4 | 18mm |
6,90 | 6,50 | 9,00 | 4.35 | 6 | 4.35 | 20mm |
8,40 | 7,80 | 11,0 | 5.2 | 7.2 | 5.2 | 22mm |
10,0 | 9,40 | 13,5 | 6.3 | 8.8 | 6.3 | 24mm |
11,8 | 11,0 | 15,0 | 7.2 | 10 | 7.2 | 26mm |
13,5 | 12,5 | 18,0 | 8.4 | 11.8 | 8.4 | 28mm |
18,0 | 16,5 | 23,5 | 11 | 15 | 11 | 32mm |
22,5 | 21,0 | 29,0 | 14 | 19 | 14 | 36mm |
28,0 | 26,0 | 36,0 | 17 | 23.5 | 17 | 40mm |
33,5 | 31,5 | 44,0 | 21 | 29 | 21 | 44mm |
40,0 | 37,0 | 52,0 | 25 | 35 | 25 | 48mm |
47,0 | 44,0 | 62,0 | 29 | 40 | 29 | 52mm |
54,0 | 50,0 | 71,0 | 33.5 | 47 | 33.5 | 56mm |
63,0 | 58,0 | 81,0 | 39 | 54 | 39 | 60mm |
1,6 | 1,5 | 2,1 | 1 | 1,4 | 1 | leg factor KL |
Working Load Limits & Safe Working Loads | ||||||
The working load limits of slings made from general engineering ropes to BS EN 12385-4 should conform to BS EN 13414-1: 2003. Note that the working load limits shown are based on the assumption that soft-eyes of single-part slings are used over bearing points of not less than twice the normal diameter of the rope. All sling ropes must be ordinary lay . | ||||||
The Safe Working Load will normally be equal to the Working Load Limit but in some circumstances it may be less e.g. If the sling is used in choke hitch SWL=WLL x 0.8 | ||||||
BS EN 13414-1 covers only those sling assemblies that have legs of equal nominal length, diameter, construction and tensile grade. While sling assemblies with legs of unequal length may be made up generally in accordance with the requirements of BS EN 13414-1, it must be stressed that their rating requires special consideration by a competent person | ||||||
Caution | ||||||
In all cases, where hooks or shackles are used, the WLL of the hooks and shackles shall never be less than the WLL of the leg which they are fitted to | ||||||
Safety recommendations | ||||||
When using multi-leg sling assemblies, remember that increasing the angles between the legs will increase the load in each leg. Examine all slings before use, and discard any that are defective. Slings which are found to be unfit for use should be destroyed by cutting them up – not put on a refuse dump. ‘Hooking back’ to the leg of a sling is not recommended. The Safe Working Load of slings is affected by the method of usage. Check that the crane hook is positioned over the loads centre of gravity to prevent swinging when the load is being raised. Correct signals, according to the recognised code, should be given to the crane driver. The signals must be given by the person responsible for the lift and nobody else | ||||||
Keep the wire rope sling away from welding and flame cutting operations. The Law requires that all lifting tackle must be examined by a competent person at regular intervals. Users should not store away slings and regard them as their own private slinging assemblies, as this could lead to them being overlooked at inspection time |
Where is the products’ country of origin?
Answer: Most of the products are from China, Korea, Germany, Ukraine, and all of them are of the most reputable factories with quality control certificate.
Does Hardwire take the responsibility for shipping products?
Answer: If the customer determines how to send the products and cargo, all responsibility is on the customer, but if Hardwire determines how to send and transport the products, it assumes all responsibilities and any damages.
How long does it take to send and deliver products?
Answer: Since the main import of Hardwire is wire rope, all types of wire ropes are almost always available in stock and delivery of goods is made instantly. Delivery for all products in all categories is immediate. If some items are not available, the delivery time will be a maximum of one week.
How is the after-sales service?
Answer: Hardwire’s after-sales service varies by product type. For example, for electric and manual cranes, Hardwire offers a one-year warranty and a period of 5 year after-sales service.
Wire rope slings are popular because they are kink resistant and provide strength and flexibility. Wire rope slings are easier to use and less expensive than chain slings. They are usually the best choice for extremely heavy lifting.
Hardwire imports all types of wire ropes including drilling line, tower crane, elevator, guy wire and non-rotating wire ropes; different types of chains; electric, off-road and hand winch; electric, manual and pneumatic hoists; lifting magnet, polypropylene and nylon ropes, rigging hardware including different types of hooks, clamp, webbing strap, master link, plate clamp, drum lifting clamp, swivel, turnbuckle, connecting link and so on; lever and pulling hoists; anchor and anchor accessories. Read more on about page
کلیه حقوق مادی و معنوی متعلق به هارد وایر می باشد
ارتباط از طریق واتساپ